500,000+ units shipped. Free shipping on orders over $299. Get Quote
Blog

xTool S1 Checklist: 7 Steps Before Your First Metal or Glass Project

I burned through roughly $380 in brass blanks, borosilicate squares, and stainless steel wallet cards during my first six weeks with the xTool S1. Not because the machine is bad—for the price, it's genuinely solid. But because I skipped the boring prep steps that most tutorials gloss over.

This checklist is what I wish someone had handed me on day one. Seven steps. Roughly 30–40 minutes of prep before your first metal or glass project. It won't make you an expert, but it'll keep you from trashing your first batch of materials.

Before You Start: Who This Checklist Is For

This is for xTool S1 owners who are about to attempt metal or glass marking for the first time—or who tried once, got a gray smudge instead of a crisp mark, and want to figure out why. If you're already comfortable with both materials, you probably know most of this. If you're not, the order matters.

Step 1: Verify Your Module's Actual Specs

The S1 ships with different laser module options—10W, 20W, and 40W in the current lineup. They don't perform the same on metal, and they don't perform the same on glass. I went back and forth between the 20W and 40W for almost two weeks before ordering. The 40W promised more cutting headroom; the 20W was cheaper and claimed a tighter spot size. I ultimately went with the 20W because most of our work is marking, not cutting.

That was the right call for us. But I should note—if you're planning to cut thick acrylic or wood on the same machine, the 40W buys you real headroom. That said, if metal marking is your main goal, extra wattage doesn't help as much as you'd think. On a diode laser, the difference between 20W and 40W on coated metal is measurable but not dramatic. The bottleneck is the wavelength, not the power.

Checkpoint: Before buying materials, confirm your module's optical power and spot size from the official xTool S1 laser cutter specs page—not from a reseller listing. I've seen listings quote “40W combined” for machines that actually ship a 10W module plus a 20W upgrade in the box. That's not the same thing.

Step 2: Clean the Optics Before Every Single Job

This is the step I skipped, and it's the one that cost me the most. Cleaning your xTool S1 isn't optional maintenance—it's a precondition for consistent results. Residue on the lens scatters the beam. Scattered beam means uneven marks, scorched edges, and on glass, hairline fractures that don't show up until the piece cools.

We didn't have a formal cleaning process for the first month. Cost us when a batch of twelve acrylic keychains came out with a hazy, inconsistent etch—the lens had a film of vaporized adhesive on it from a previous job, and I never checked. Twelve pieces, about $40 in material, straight to the scrap bin.

The third time it happened, I finally created a two-minute pre-flight routine:

  • Wipe the lens with 99% isopropyl alcohol and a lint-free swab (not a paper towel—paper towels leave fibers).
  • Check the laser window for soot buildup. It's a small protective pane; if you can see a gray film, clean it.
  • Empty and wipe the honeycomb tray. Metal dust accumulates fast, and on a diode laser it's a genuine fire risk—not a theoretical one.
  • Check the exhaust fan intake. If you're cutting leather or MDF regularly, it clogs faster than you'd expect.

Note to self: label the swab container so nobody grabs the wrong one. (We had a mix-up with acetone once. That was a $60 lens.)

Step 3: Understand What a Diode Laser Can Actually Do on Metal

Here's the part most listings don't emphasize enough. The xTool S1 is a diode laser. On bare, uncoated metal, it doesn't mark. Not “marks weakly.” Doesn't mark. The 450nm wavelength reflects off bare metal surfaces rather than being absorbed.

What it will do:

  • Mark coated metals (anodized aluminum, painted steel, powder-coated brass) by removing or altering the coating.
  • Mark stainless steel using a marking spray or coating—xTool sells one, and CerMark is the industry-standard alternative. The laser fuses the coating to the metal surface.
  • Produce color marking on stainless steel at specific power/speed combinations (oxide layer formation). This is finicky and machine-specific—expect to iterate.

What it won't do: deep-engrave or cut bare metal. If that's your requirement—say, serial-number engraving into tool steel—don't buy a diode laser for it. That's a fiber laser job, or outsource it. I'd rather tell you that now than have you find out after spending $400 on a machine and another $200 on ruined blanks.

Checkpoint: If a listing claims a diode laser “cuts 1mm steel,” read the fine print. It almost always means “marks coated steel after multiple passes.” That's not cutting.

Step 4: Glass Marking Depends Entirely on the Glass

The xTool S1 can mark glass, but the results vary more than any other material we've tested—and the difference comes down to the glass itself, not the settings.

Dark or colored glass marks reliably. Clear borosilicate is difficult. Standard soda-lime glass (the cheap stuff) is somewhere in between. I went through four separate batches of clear glass before I accepted that the issue wasn't my parameters—it was the fact that clear glass lets most of the 450nm beam pass straight through.

What worked for us in the end:

  • For dark glass: direct marking at moderate power, high speed, one pass. Let it cool completely before touching—the mark looks faint when hot and darkens as it cools.
  • For clear glass: apply a thin layer of marking tape or a wet paper towel over the surface. The laser heats the coating, which transfers heat to the glass and creates controlled microfractures. It's not the same look as etched glass—more of a frosted, stippled texture—but it's consistent.
  • Skip tempered glass entirely unless you're prepared for pieces to shatter. Heat stress on tempered glass is unpredictable, and I've seen it crack after a mark that looked fine.

After the third failed batch of clear glass, I was ready to write off glass marking altogether. What helped was stopping mid-process and testing one variable at a time instead of changing three settings simultaneously. Basic, but I had to learn it the hard way.

Step 5: Run Your First Tests on Free Files, Not Paid Materials

Before you burn through your stock of brass blanks, download a few free laser engraving files and run them on scrap. Free files are everywhere—xTool's own Creative Space library, Thingiverse's laser-cut section, and most of the active xTool Facebook groups maintain shared folders. Etsy has free sample packs too, though they rotate.

One caution: the parameters that ship with a free file are almost always calibrated to someone else's machine and module. I downloaded a popular business card template that recommended 60% power at 300mm/min—ran it on our 20W module and got a scorched, illegible mess. The template was designed for a 40W. Different wavelength concentration, different result.

Treat free files as geometry, not as recipes. Copy the design, ignore the settings, then run your own parameter test (Step 6) on that specific material before you commit.

Step 6: Run a Parameter Test Grid—Every Time, New Material

This is the step that separates people who get consistent results from people who get lucky results. Every new material—every new batch of a material, sometimes—needs a test grid.

On metal, I use a 3×3 or 4×4 grid of small filled squares, varying power across one axis and speed across the other. Twelve combinations, two minutes of laser time, and you can see exactly where the mark transitions from “nothing” to “just right” to “burned through the coating.” We keep a printed sheet of these grids on the wall next to the machine with the date and material lot written on it.

On glass, I use a simpler two-variable test: power (three levels) × number of passes (one, two, three). Glass tends to either mark or not—the middle ground is narrow, and pass count matters more than speed.

Checkpoint: Photograph the grid next to the actual settings. I can't count how many times I've found the perfect parameter combination and then couldn't remember which square on the test grid it corresponded to.

Step 7: Keep a Parameter Log (Yes, Actually)

For the first two months, I kept settings in my head and on random sticky notes stuck to the laser enclosure. That lasted until a sticky note fell off and landed inside the work area while a job was running. Nothing caught fire, but that was luck, not design.

Now we keep a shared Google Sheet with a row for every material that's ever passed through the machine. Columns: material name, supplier, batch date, module, power, speed, passes, coating (if any), result notes, and a photo link. That's it. No fancy system. If you're a solo operator, a notebook works fine. The point is having some record, because your memory of “that one setting that worked” fades faster than you think.

We've caught 40-some potential errors using this log over the past 18 months. Roughly 20 of those were batch-to-batch differences in the same “material”—the same 0.5mm anodized aluminum from the same supplier behaved differently across three orders. Without the log, we would've assumed the settings were wrong instead of the stock.

A Few Things That Don't Fit in the Steps

Ventilation isn't optional. Marking spray fumes, vaporized coating, and glass dust are all things you don't want to breathe. A window fan pulling air outside is a minimum. If you're running the S1 in a living space, build or buy an enclosure. This is standard laser safety practice—not xTool-specific. FDA's 21 CFR 1040.10 regulations on laser products are what you want to look at if you ever wonder why the enclosure interlocks exist.

Don't bypass the safety interlock. The S1 is classified as a Class 1 product only when the lid is closed. Open the lid while the laser is active and it becomes a Class 4 exposure. The interlock exists for a reason. I've seen one person tape it shut “for testing” and I've never let them near our machine since.

Be honest about your project's scope. The S1 handles a huge range of work—wood, leather, acrylic, anodized aluminum, coated metals, and dark glass. It's a genuinely capable machine for a small shop. But if your workload suddenly shifts toward production metal engraving or thick steel cutting, the S1 is the wrong tool. I'd rather send a customer to a fiber-laser shop than promise something we can't deliver. That's not a weakness in the machine. It's just a boundary worth knowing.

Run the checklist. Test on scrap. Document what worked. The first twenty minutes of prep saves the next four hours of rework. Every time.

WhatsApp X LinkedIn
Jane Smith

Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply